Wearing away by friction.
Ability of a surface to resist being worn away by rubbing and friction.
Moisture that has entered a solid material by absorption and has physical properties not substantially different from ordinary water at the same temperature and pressure. (See also Absorption.)
The relationship of the weight of the water absorbed by a ceramic specimen subjected to prescribed immersion procedure to the weight of the dry /specimen expressed in percent. (ASTM C 242).
A substance which when added to concrete mortar or grout increases the rate of hydration of the hydraulic cement shortens the time of setting or increases the rate of hardening of strength development or both. (See also Acceleration.)
A chemical substance usually corrosive to common metals (iron aluminum zinc) and which, in water solution, imparts an acid sour or tart taste. Acids are generally divided into two classes: (a) strong mineral or inorganic acids
A general term applying to substances on the acid side of neutral - principally the degree of acidity. A general class of resinous polymers derived from esters amides or other acrylic acid derivatives.
A term frequently (but improperly) used as a synonym for addition or admixture.
Adhesion between surfaces in which the adhesive holds the parts together by interlocking action. (See also Adhesion specific.)
Adhesion between surfaces which are held together by valence forces of the same type as those which give rise to cohesion. (See also Adhesion mechanical.)
An adhesive made so as to adhere to a surface at room temperature by briefly applied pressure alone.
An adhesive having a volatile organic liquid as a vehicle. Note: This term excludes water based adhesives.
A material, other than water, aggregates and hydraulic cement used as an ingredient of concrete or mortar and added to the concrete immediately before or during its mixing.
Aggregate of low specific gravity such as expanded or sintered clay shale. slate diatomaceous shale
Aggregate of high specific gravity such as barite magnetite limonite ilmenite iron or steel used to produce heavy concrete. Aggregate lightweight.
The capability of a material or process to develop a system of minute bubbles of air in cement mortar or concrete during mixing.
The occlusion of air in the form of minute bubbles (generally smaller than 1mm) during the mixing of concrete or mortar. (See also Air entraining and Entrained air.)
A chemical substance which effectively neutralizes acid material so as to form neutral salts. A base. The opposite of acid. Examples are ammonia and caustic soda.
The wall facing an observer who is standing at the entrance to a room shower or tub shower. Backing. Any material used as a base over which a finished material is to be installed.
See Featheredging tile. Angle tile. See under Tile mounted.
Cuts of tile at the perimeter of an area that will not take full tiles. The cuts on opposite sides of such an area shall be the same size. Also the same sized cuts on each side of a miter.
A secondary clay commonly characterized by the presence of organic matter high plasticity high dry strength long vitrification range and a light color when fired. (ASTM C 242).
A method of grinding and mixture material with or without liquid in a rotating cylinder or conical mill partially filled with grinding media such as balls or pebbles. (ASTM C 242).
A rigid device used to support or hold reinforcing bars in proper position to prevent displacement before or during concrete placement.
A black unglazed vitreous ceramic ware having the appearance of basalt rock. (ASTM C 242). Base. One or more rows of tile installed above the floor. See Cove.
Basis for acceptance
The method of determining whether a lot of ceramic tile is acceptable under these specifications.
A machine which mixes batches of concrete or mortar in contrast to a continuous mixer.
An operating installation of equipment including batchers and mixers as required for batching or for batching and mixing concrete materials; also called mixing plant when equipment is included.
A wooden block used to embed tiles in a flat plane. The method used is called beating in.
A highly translucent whiteware composed of a body containing a significant amount of frit and normally having a luster glaze. (Produced commercially at Belleek Ireland.) (ASTM C 242).
Permanent reference point or mark.
A clay composed principally of minerals of the montmorillonoid group charactersized by high absorption and very large volume change with wetting or drying.
Beryllium oxide (berylla) (BeO)
An inorganic material of exceptionally high thermal conductivity which is toxic in the powder form.
Glazed-over chips on the edge or corner of the body of a tile.
Any fractures in the body of a tile visible both on face and back.
See Fire bisque.
The fineness of powdered materials such as cement and pozzolans expressed as surface area usually in square centimeters per gram determined by the Blaine apparatus.
A small blister or bubble.
The autogenous flow of mixing water within or its emergence from newly placed concrete or mortar; caused by the settlement of the solid materials within the mass; also called water gain.
To mix or make homogeneous.
The development during firing of enclosed or broken macroscopic vesicles or bubbles in a body or in a glaze or other coating. (ASTM C 242).
A square of tile specially made for changing direction of the trim.
A visible exudation or efflorescence on the surface.
Green marks or stains on the face of a tile.
The wet process of blending or suspending ceramic material in liquid by agitation. (ASTM C 242). The structural portion of a ceramic article. This term also refers to the material or mixture from which the article is made. (ASTM C 242).
The adherence of one material to another. Effective bonds must be achieved between the mortar and scratch coat between the tile and mortar and between the adhesive and backing.
A material used to prevent adhesion of newly placed concrete and the substrate.
A material used between the back of the tile and the prepared surface. Suitable bond coats include pure portland cement Dry-Set portland cement mortar latex-type portland cement mortar organic adhesive and the like.
A substance applied to a suitable substrate to create a bond between it and a succeeding layer as between a subsurface and a terrazzo topping or a succeeding plaster application.
Calcined bone consisting essentially of calcium phosphate. (ASTM C 242).
A translucent china made from a ceramic whiteware body composition containing a minimum of 25 percent bone ash. (ASTM C 242).
The brick trowel is larger than the buttering trowel. The most popular size used by tilesetters is 5" wide and 11" long. It is used when any preparatory brick work has to be done. Some tilesetters use it for quarry and terra cotta tilework. Its greater sur
A straightedge used as a starting line for the laying of tile. The straightedge can be blocked up to support tile over an opening.
The slab or other structure forming the travel surface of a bridge.
Colorless or colored ceramic glaze having high gloss. (ASTM C 242).
The surface texture obtained by stroking a broom over freshly placed concrete. (See also Brushed surface.)
The second coat in three-coat plaster application.
A sandy texture obtained by brushing the surface of freshly placed or slightly hardened concrete with a stiff brush for architectural effect or in pavements to increase skid resistance. (See also Broom finish.)
The official charged with administration and enforcement of the applicable building code or his duly authorized representative.
Increase in the bulk volume of a quantity of sand in a moist condition over the volume of the same quantity dry or completely inundated.
Graph of change in volume of a quantity of sand due to change in moisture content.
Ratio of the volume of moist sand to the volume of the sand when dry.
A tool comprising a large flat rectangular piece of wood aluminum or magnesium usually 8 in. (20 cm) wide and 42 to 60 in. (100 to 150 cm) long and a handle 4 to 16 ft. (1 to 5 cm) in length used to smooth unformed surfaces of freshly placed concrete.
A trim tile with a convex radius on one edge. This tile is used for finishing the top of a wainscot or for turning an outside corner.
A type of bullnose trim with a convex radius on two adjacent edges.
A group of not more than four parallel reinforcing bars in contact with each other usually tied together.
A coarse fabric of jute hemp or less commonly flax for use as a water-retaining covering in curing concrete surfaces; also called Hessian.
A hammer that has a rectangular head with serrated or jagged faces. The bushhammer is used for roughing concrete to provide a bond for masonry. Butterfly. A slang term for inside corner angles for trim shapes such as AB 106 AF 105 AF 200 AK 106 and AU
A plain square joint between two members.
The spreading of a bond coat (followed by a mortar coat a thin-setting bed mortar or an organc adhesive) to the backs of ceramic tile just before the tile is placed.
The blade of the buttering trowel is 41/2' wide and 7" long. It is used in buttering pure cement to tile a method commonly used in the eastern states. The trowel is more efficient than the pointer for working on the larger and heavier tiles
Tile that have projections on the bondable side. Many of these projections are round and therefore the term buttonback. Some projections are quite thick and can also be other shapes such as square.
A ceramic mineral or mixture fired to less than fusion for use as a constituent in a ceramic composition. (ASTM C 242).
A deflection that is intentionally built into a structural element or form to improve appearance or to nullify the deflection of the element under the effects of loads shrinkage and creep.
Cassiterite (Sri 02)
An inorganic mineral of the tetragonal form used as a source of tin and tin oxide. (ASTM C 21)
Forming ceramic ware by introducing a body slip into a porous mold which absorbs sufficient water from the slip to produce a semirigid article. (ASTM C 242).
Casting drain (hollow casting)
Forming ceramic ware by introducing a body slip into an open porous mold and then draining off the remaining slip when the cast has reached the desired thickness. (ASTM C 242).
A fast-setting gypsum plaster that is used to anchor marble to walls set spots or mix temporary "hot mud."
Forming ceramic ware by introducing a body slip into a porous mold which usually consists of two major sections one section forming the contour of the inside of the ware and allowing a solid cast to form between the two mold faces. (ASTM C 242).
Mortar or concrete which is deposited in the place where it is required to harden as part of the structure as opposed to precast concrete.
A soft plastic material consisting of pigment and vehicle used for sealing joints in buildings and other structures where normal structural movement may occur.Caulking compound retains its plasticity for an extended period after application.
Extra-rich wall mortar.
Usually refers to portland cement which when mixed with sand gravel and water forms concrete. Generally cement is an adhesive; specifically it is that type of adhesive which sets by virtue of a chemical reaction.
A cementitious mixture of portland cement sand or other ingredients and water which produces a water resistant uniformly colored material used to fill joints between tile units.
A hydraulic cement for use in mortars for masonry construction containing one or more of the following materials: portland cement portland blast-furnace slag cement portland-pozzolan cement natural cement slag cement or hydraulic lime; and in addition
A cementitious mixture of portland cement sand or other ingredients and water which is used for bonding tile to back-up material.
A hydraulic cement produced by pulverizing clinker consisting essentially of hydraulic calcium silicates and usually containing one or more of the forms of calcium sulfate as an interground addition. Cement white.
Tiles with the body made from a mixture of sand and portland cement. The surface may be finished with portland cement spheroids of marble or other materials.
A scale of temperature which features 0? and 100? as the freezing and boiling point of water respectively. To convert centigrade to Fahrenheit multiply by 1.8 and add 32 e.g. (100?x1.8)- 32=212?F.
An article having a glazed or unglazed body of crystalline or partly crystalline structure or of glass which body is produced from essentially inorganic nonmetallic substances and either is formed from a molten mass which solidifies on cooling or is for
Ceramic mosaic tile
An unglazed tile formed by either the dust-pressed or plastic method usually 1/a to 3/a in. (6.4 to 9.5 mm) thick and having a facial area of less than 6 in. 2 and which is usually mounted on sheets approximately 2 by 1 ft. (0.3 by 0.6 m) to facilitate s
The production of articles or coatings from essentially inorganic nonmetallic materials the article or coating being made permanent and suitable for utilitarian and decorative purposes by the action of heat
A ceramic surfacing unit usually relatively thin in relation to facial area made from clay or a mixture of clay; and other ceramic material called the body of the tile having either a "glazed" or "unglazed" face and fired above red heat
A fired ware consisting of a glazed or unglazed ceramic body which is commonly white and of fine texture. This term designates such products as china porcelain semivitreous ware and earthenware. (ASTM C 242).
A general term applied to the art or technique of producing articles by a ceramic process or to the articles so producing. (ASTM C 242).
See Bar support.
Usually cotton cord coated with chalk. The cord is snapped to mark a straight line. The chalk line is used to align spots or screeds.
Short shallow cracks on the surface. Chemical porcelain. Vitreous ceramic whitewares used for containing transporting or reacting of chemicals. (ASTM C 242).
A glazed or unglazed vitreous ceramic whiteware used for nontechnical purposes. This term designates such products as dinnerware sanitary ware and art ware when they are vitreous. (See also Bone china.) (ASTM C 242).
The method of producing glazed ware by which the ceramic body is fired to maturity following which the glaze is applied and matured by firing at a lower temperature. (ASTM C 242).
China sanitary ware (sanitary plumbing fixtures)
Glazed vitrified whiteware fixtures having a sanitary service function. (ASTM C 242).
Caused from the same reasons as given under "pitted" or by rough handling and confined to the corners and edges of the tile.
The chipping hammer is a lightweight hammer that comes in a variety of sizes. The head and back can be capped with tungsten carbide for durability. It is used by the tilesetter to chip excess material from the backs and edges of wall and quarry tiles thus
The scaling or breaking off at the edges of fragments from the surface of a tile as might result from rough handling.
A natural mineral aggregate consisting essentially of hydrous aluminum silicates; it is plastic when sufficiently wetted rigid when dried en masse and vitrified when fired to a sufficiently high temperature. (ASTM C 242).
A colorless or colored transparent ceramic glaze. (ASTM C 242).
A layer of 15 lb. roofing felt or an equivalent type of construction paper or polyethylene sheeting used to isolate a wire reinforced mortar bed for tile from the concrete substrate. (CTI)
Any point in a tile installation where tile and setting bed have terminated and the surface has lost its plasticity before work is continued.
Cold joint lines
Visible lines on the surfaces of formed concrete indicating the presence of joints where one layer of concrete had hardened before subsequent concrete was placed. (See also Cold joint).
The aspect of the appearance of an object dependent upon the spectral composition of the incident light the spectral reflectance of transmittance of the object and the spectral response of the observer.
Commercially prepared grout consisting of carefully graded aggregate portland cement water dispersing agents plasticizers and color fast pigments. (CTI).
A member used primarily to support axial compression loads and with a height of at least three times its least lateral dimension.
The process whereby the volume of freshly placed mortar or concrete is reduced to the minimum practical space usually by vibration centrifugation tamping or some combination of these; to mold it within forms or molds.
A hard tile surfacing unit made from a mixture of chemicals. The finished surface can be the mixture of chemicals or can be marble chips to create a terrazzo finish. The unit is made hard by the set of the chemicals.
The measured maximum resistance of a concrete or mortar specimen to axial loading; expressed as force per unit cross-sectional area; or the specified resistance used in design calculations in the U.S. customary units
A composite material which consists essentially of a binding medium within which are embedded particles or fragments of aggregate; in portland cement concrete the binder is a mixture of portland cement and water.
An apparatus which forces concrete to the placing position through a pipeline or hose. Concrete prestressed. See Prestressed concrete. Concrete pumped. See Pumped concrete.
Concrete containing dispersed randomly oriented fibers.
Concrete delivered or mixed placed and cured on the job site.
Concrete made very light and cellular by the addition of a prepared foam or by generation of gas within the unhardened mixture.
Concrete which has set but not appreciably hardened.
See Precast concrete.
See Refractory concrete.
Marble-aggregate concrete that is cast-in-place precast and ground smooth for decorative surfacing purposes on floors and walls.
Usually refers to liquid drops which form when a vapor is chilled below its boiling point. Also refers to water droplets that deposit on surfaces whose temperature is below the dewpoint.
Having the quality or power of conducting or transmitting heat electricity or static electricity.
A tile mortar to which specific electrical conductivity is imparted through the use of conductive additives. (TCA)
Tile made from special body compositions or by methods that result in specific properties of electrical conductivity while retaining other normal physical properties of ceramic tile. (SS-T-308b)
Stained tile as a result of carton and tile being saturated by moisture oils solvents or other materials.
Formed sawed or tooled groove in a concrete structure to create a weakened plane and regulate the location or cracking resulting from the dimensional change of different parts of the structure. (See also Isolation joint.)
See Expansion joints.
The method of installing ceramic tile with portland cement mortar.
The material or units used to form a cap or finish on top of a wall pier pilaster or chimney.
A projection from the face of a beam girder column or wall used as a beam seat or a decoration.
A vitreous ceramic whiteware for technical application in which cordierite (2 MgO 2A120. 3 - 5SiO2) is the essential crystalline phase. (ASTM C 242).
Anv ceramic whiteware in which cordierite (2MgO - 2A1203 - 5SiO2) is the essential crystalline phase. (ASTM C 242).
The eating and wearing away by chemical action (pitting rusting).
A trim tile unit having one edge with a concave radius. A cove is used to form a junction between the bottom wall course and the floor or to form an inside corner. (TCA)
Cove base (sanitary)
A trim tile having a concave radius on one edge and a convex radius with a flat landing on the opposite edge. This base often is used as the only course of tile above the floor tile.
A measure of the amount of material required to cover a given surface.
The ability of a glaze to uniformly and completely cover the surface of the fired water. (ASTM C 242).
Reinforcement in concrete construction designed to prevent opening of cracks often effective in limiting them to uniformly distributed small cracks.
Tiles that have actually been cracked in one or more pieces usually during the beating in process of installation. These will show up as hairline cracks.
A parting and contraction of the glaze on the surface of ceramic ware during drying or firing resulting in unglazed areas bordered by coalesced glaze. (ASTM C 242-58T)
The cracking which occurs in fired glazes or other ceramic coatings due to critical tensile stresses. (ASTM C 242).
Tune-dependent deformation due to sustained load.
A curvature of the sides either convex or concave measured along the sides. The degree of crook is the departure from the straight line between two corners expressed in percentage of the tile length.
Glazed tile with an extra heavy glaze produced for use on counter tops and light duty floor surfaces where abrasion or impact is not excessive. (CTI)
Maintenance of humidity and temperature of freshly placed concrete during some definite period following placing casting or finishing to assure satisfactory hydration of the cementitious materials and proper hardening of the concrete.
A built-up covering of sacks matting hessian straw waterproof paper or other suitable material placed over freshly finished concrete. (See also Burlap.)
A liquid that can be applied as a coating to the surface of newly placed concrete to retard the loss of water or in the case of pigmented compounds also to reflect heat so as to provide an opportunity for the concrete to develop its properties in a favor
A system in which a favorable temperature is maintained in freshly-placed concrete by supplying heat generated by electrical resistance. Curing steam. See Steam curing.
The distortion of an originally essentially linear or planar member into a curved shape such as the warping of a slab due to creep or to differences in temperature or moisture content in the zones adjacent to its opposite faces.
Tile on which the facial edges have a distinct curvature that results in a slightly recessed joint.
A slang term used to describe the use of a fresh mortar screed in lieu of float strips to rod floor mortar. This method is commonly used in floor work. Italian terrazzo workers use this technique to align "concrete" for placement of brass or aluminum strip
A slang term used by tilesetters when referring to a small piece of wood used to rod off mortar that has been applied to fill the holes caused by the removal of float strips.
A hand-manipulated straightedge usually 3 to S ft. (1 to 2.5) long used in the early stage leveling operations of concrete or plaster preceding supplemental floating and finishing.
A thick slurry of portland cement sand and water flicked on surfaces with a paddle or brush to provide a base for subsequent portland cement plaster coats; sometimes used as a final finish on plaster.
The progressive formation on a concrete surface of a series of fine cracks at rather close intervals often of random patterns but in slabs on grade paralleling edges joints and cracks and usually curving across slab corners.
The form on which concrete for a slab is placed also the floor or roof slab itself. (See also Bridge deck.)
Deck or floor mortar
Mortar commonly used for decks or floors. It consists of sand and regular portland cement mixed with water to a firm consistency.
Adorned embellished or made more attractive by means of color or surface detail. (ASTM C 242).
See Fire decorating.
See Decoration inglaze; Decoration overglaze; Decoration underglaze.
A ceramic decoration applied on the surface of an unfired glaze and matured with the glaze. (ASTM C 242).
A ceramic or metallic decoration applied and fired on the previously glazed surface of ceramic ware. (ASTM C 242).
A ceramic decoration applied directly on the surface of ceramic ware and subsequently covered with a transparent glaze. (ASTM C 242).
Tile with a ceramic decoration on the surface. (See heading under Decorated and Decoration.)
A variation in position or shape of a structure or structural element due to effects of loads or volume change usually measured as a linear deviation from an established plane rather than an angular variation.
See Eutectic deformation.
A calcareous earthenware having an opaque white glaze and monochrome overglaze decorations. (Originated in Delft Holland.) (ASTM C 242).
Ceramic whiteware made in a given pattern and in a full line of articles comprising a dinner service. (ASTM C 242).
Departure of color from that which is normal or desired.
In terrazzo work nonferrous metal or plastic strips of different thickness and embedded depths usually 5/s to 1'/4 in. (10 to 40 mm) used to form panels in the topping.
A constant load that in structures is due to the mass of the members the supported structure and permanent attachments or accessories.
The double carbonate of lime and magnesia having the general formula CaCO3 MgCA3. (ASTM C 242).
Neat cement applied to the setting bed. Double bullnose. A type of trim with the same convex radius on two opposite sides.
Double headed nail
A nail with two heads at or near one end to permit easy removal; widely used in concrete formwork.
A steel pin commonly a plain round steel bar which extends into two adjoining portions of a concrete construction as at a joint in a pavement slab so as to connect the portions and transfer shear loads.
See Casting drain.
Rough edges and corners of glazed ceramic ware due to insufficient glaze coating. (ASTM C 242). Dry mix. See Process dry.
Concrete or mortar mixtures deposited and consolidated by dry packing.
Placing of zero slump or near zero slump concrete mortar or grout by ramming into a confined space.
See Pressing dry.
See Process dry.
Small areas on the face of tile which have been insufficiently glazed.
Removal by evaporation of uncombined water or other volatile substance from a ceramic raw material or product usually expedited by low temperature heating. (ASTM C 242).
A water-retentive hydraulic cement mortar usable with or without sand. When this mortar is used neither the tile nor walls have to be soaked during the installation process.
The cracking that occurs in fired ceramic bodies due to thermally induced stresses. (ASTM C 242-72)
The application of dry portland cement to a wet floor or deck mortar surface. A pure coat is thus formed by suction of the dry cement.
A cut tile used as a filler in the run of a wall or floor area.
A slang term used by tilesetters when referring to a mortar accelerator.
A 6"x3/4" outside corner trim shape. (AC 106) Earthenware. A glazed or unglazed nonvitreous ceramic whiteware. (ASTM C 242).
See definition for Pregrouted tile.
A type of mounted tile wherein tile is assembled into units or sheets and are bonded to each other at the edges or corners of the back of the tiles by an elastomeric or resinous material which becomes an integral part of the tile installation. Units or she
The residue deposited on the surface of a material by the crystallization of soluble salts. A finishing tool used on the edges of fresh concrete to provide a rounded corner.
The texture of a fired glaze similar in apperance to the surface of an eggshell. (ASTM C 242). Electrical porcelain. Vitrified whiteware having an electrical insulating function. (ASTM C 242). Electrolysis.
A decoration in relief or excised on the ware surface. (ASTM C 242).
A decoration in relief or excised on the ware. (ASTM C 242).
A slip coating applied to a ceramic body for imparting color opacity or other characteristics and subsequently covered with a glaze. (ASTM C 242).
Microscopic air bubbles intentionally incorporated into mortar or concrete during mixing usually by use of a surface-active agent typically between 10 and 1 000 N.m in diameter and spherical or nearly so. (See also Air entrainment.)
A two-part adhesive system employing epoxy resin and epoxy hardener used for bonding of ceramic tile to back-up materials.
A two-part grout system consisting of epoxy resin and epoxy hardener especially formulated to have impervious qualities stain and chemical resistance used to fill joints between tile units.
A two-part mortar system consisting of epoxy resin and epoxy hardener used to bond tile to back-up material where chemical resistance of high bond strength is a consideration.
An epoxy composition used as a chemicalresistant setting adhesive or chemical-resistant grout.
See Eutectic equilibrium. Eutectic. See Eutectic deformation; Eutectic equilibrium.
deformation The composition within a system of two or more components which on heating under specific conditions develops sufficient liquid to cause deformation at minimum temperature. (ASTM C 242). Eutectic equilibrium (eutectic).
A joint through tile mortar and reinforcing wire down to the substrate.
A decorative finish for concrete work achieved by removing generally before the concrete has fully hardened the outer skin of mortar and exposing the coarse aggregate.
Extra duty tile
See Special purpose tile.
A tile or trim unit that is formed when plastic clay mixtures are forced through a pug mill opening (die) of suitable configuration resulting in a continuous ribbon of formed clay. A wire cutter or similar cut-off device is then used to cut the ribbon int
That portion of the facial surface of the tile which is readily observed to be nonconforming and which will detract from the aesthetic appearance or serviceability of the installed tile.
Faience the that are less than 6 in .z in facial area usually 5/16 to 3/8 in. (8 to 9.5 mm) thick and usually mounted to facilitate installation. (ASTM C 242).
Faience the that are less than 6 in .z in facial area usually 5/16 to 3/8 in. (8 to 9.5 mm) thick and usually mounted to facilitate installation. (ASTM C 242).
Glazed or unglazed tile generally made by the plastic process showing characteristic variations in the face edges and glaze that give a handcrafted nonmechanical decorative effect. (ASTM C 242).
Formerly a decorated earthenware with an opaque glaze but currently designating a decorated earthenware having a transparent glaze (ASTM C 242).
Fan or fanning
Spacing tile joints to widen certain areas so they will conform to a section that is not parallel.
A flat member or band at the surface of a building or the edge beam of a bridge; exposed eave of a building; often inappropriately called facia.
A wood or metal tool having a beveled edge; used to straighten re-entrant angles in finish plaster coat; also edge of a concrete or mortar placement such as a patch or topping that is beveled at an acute angle.
Featheredging file (mitering)
The method of chipping away the body from beneath a facial edge of a tile in order to form a miter.
Feature strip (decorated liner)
A narrow strip of tile that has a contrasting color texture or design.
A mineral aggregate consisting chiefly of microcline albite and/or anorthite. (ASTM C 242);
The name for products made of or with glass fibers ranging from 5 to 600 hundred-thousandths inch in diameter. Used for making textile fabrics and for heat or sound insulation.
An area of tile covering a wall or floor. The field is bordered by tile trim.
See Spacing mix. Filler. See Spacing mix. Fineness modulus. A factor obtained by adding the total percentages by weight of an aggregate sample retained on each of a specified series of sieves and dividing the sum by 100.
See Spacing mix.
Final setting time
The time required for a freshly mixed cement paste mortar or concrete to achieve final set.
See Fire bisque; Fire decorating; Fire glost; Fire single.
An earthy or stony mineral aggregate which has as the essential constituent hydrous silicates of aluminum with or without free silica plastic when sufficiently pulverized and wetted rigid when subsequently dried and of suitable refractoriness for use in
The process of kiln-firing ceramic ware prior to glazing. (ASTM C 242).
The process of firing ceramic or metallic decorations on the surface of glazed ceramic ware. (ASTM C 242).
The process of kiln-firing bisque ware to which glaze has been applied. (ASTM C 242).
The process of maturing an unfired ceramic body and its glaze in one firing operation. (ASTM C 242).
The controlled heat treatment of ceramic ware in a kiln or furnace during the process of manufacture to develop the desired properties. (ASTM C. 242).
The range of firing temperature within which a ceramic composition develops properties which render it commercially useful. (ASTM C 242).
Irregularities left on the edge of the tile mainly due to the use of machine cutting tools.
Capable of being easily ignited.
The temperature at which the material gives off flammable vapor in sufficient quantity to ignite momentarily on the application of a flame under specified conditions.
The flat trowel is used in conjunction with the hawk for the transferring of mortar from the mortarboard to the wall or to other vertical surfaces. It is frequently used for spreading pure cement on the finished float coat.
A property of a material or structural member that indicates its ability to resist failure in bending. (See also Modulus of rupture.)
The final mortar coat over which the neat coat pure coat or skim coat is applied.
A strip of wood about i/4" thick and 1'/a" wide. It is used as a guide to align mortar surfaces.
A method of using a straightedge to align mortar with the float strips or screeds. This technique also is called dragging pulling rodding or rodding off.
Fluorite (Ca F2) (fluorspar)
An inorganic mineral of the isometric form used as a source of fluorine for fluxing of glasses and glazes.
A substance that promotes fusion in a given ceramic mixture. (ASTM C 242).
1. Storage of concrete in a moist room in which the desired high humidity is achieved by the atomization of fresh water. (See also Moist room). 2. Application of atomized fresh water to concrete stucco mortar or plaster.
Oil applied to interior surface of formwork to promote easy release from the concrete when forms are removed.
The shaping or molding of ceramic ware. (ASTM C 242).
A vitreous ceramic whiteware for technical application in which forsterite (2MgO SiO~ is the essential crystalline phase. (ASTM C 242).
Any ceramic whiteware in which Forstertte (2MgO - SiO ) is the essential crystalline phase. (ASTM C 242).
The application of wall mortar without the use of guide screeds. This technique is used by specialists when they are setting glass mosaic murals.
A glass which contains fluxing material and is employed as a constituent in a glaze body or other ceramic composition. (ASTM C 242).
A glaze in which a part or all of the fluxing constituents are prefused. (ASTM C 242).
Frost proof tile
Tile produced for use where freezing and thawing conditions occur. (CTI)
A two-part mortar system of furan resin and furan hardener used for bonding tile to back-up material where chemical resistance of floors is important.
Plastics based on resins in which the furan ring is an integral part of the polymer chain made by the polymerization -or polycondensation of furfural furfuryl alcohol or other compounds containing a furan ring or by the reaction of these furan compound
A furan resin composition used as a chemical-resistant setting adhesive or chemical-resistant grout.
Furan resin grout
A two-part grout system of furan resin and furan hardener used for filling joints between quarry tile and pavers where chemical resistant properties are required.
Stripping used to build out a surface such as a studded wall where strips of suitable size are added to the studs to accommodate vent pipes or other fixtures. (TCA)
The process of melting; usually the result of interaction of two or more materials. (ASTM C 242).
Formerly an earthenware with an opaque luster glaze and overglaze colored decorations but currently designating any decorated earthenware having an opaque glaze. (ASTM C 242).
Marble mosaic tile
Tile made of small marble tesserae that vary slightly in size usually about one half inch square and mounted on sheets of paper to facilitate installation. (CTI)
Marble cut into tile sizes twelve (12) inches square or less usually % inch to 3/4 inch thick. Several types of finishes are made polished honed split faced etc.
The ability of a fired glaze to mask visually the body on which it is applied. (ASTM C 242).
Master Grade certificate
A certificate that states tile listed in the shipment and described on the certificate are made in accordance with TCA 137.1-76. Mastic. Organic tile adhesive.
A chemical mixture of organic and inorganic ingredients forming a one part grouting composition that is used directly from the manufacturer's container.
A colorless or colored ceramic glaze having low gloss. (ASTM C 242).
The time-temperature range within which a ceramic body glaze or other composition may be fired to yield specified properties. (ASTM C 242-72)
Medium duty tile
Tile suitable for pedestrian traffic such as entryways in multiple dwellings and lobbys. Melt. To change a solid into a liquid by the application of heat; or the liquid resulting from such action. (ASTM C 242).
Medium duty tile
Tile suitable for pedestrian traffic such as entryways in multiple dwellings and lobbys. Melt. To change a solid into a liquid by the application of heat; or the liquid resulting from such action. (ASTM C 242).
Metal quarry tile rack
Metal quarry tile racks are available in many patterns and they can be made to order for special patterns. They are used to maintain the same width between the quarry tiles.
Mexican paver tile
Terra cotta-like tile used mainly for floors and handmade. These tile vary in color texture and appearance from tile to tile and within each tile. They are available in squares up to 12 inches hexagon octagon elongated hexagon and fleur de lis
The oxide layer formed during the hot rolling of metals such as that formed on hot-rolled reinforcing bars.
Aggregate consisting essentially of inorganic nonmetallic materials.
The act or process of mixing; also mixture of materials such as mortar or concrete.
A machine used for blending the constituents of concrete grout mortar cement paste or other mixture.
The adequacy of a mixer in rendering a homogeneous product within a stated period; homogeneity is determinable by testing for relative differences in physical properties of samples extracted from different portions of a freshly mixed batch.
A horizontally rotating drum mixer that charges mixes and discharges without tilting.
See Batch plant.
A mixer designed to produce colloidal grout.
Mixer, horizontal shaft
A mixer having a stationary cylindrical mixing compartment with the axis of the cylinder horizontal and one or more rotating horizontal shafts to which mixing blades or paddles are attached.
A truck-mounted mixer consisting of a trough or a segment of a cylindrical mixing compartment within which paddles or blades rotate about the horizontal axis of the trough. (See also Mixer horizontal shaft.)
See Mixer vertical shaft.
A rotating drum mixer that discharges by tilting the drum about a fixed or movable horizontal axis at right angles to the drum axis. The drum axis may be horizontal or inclined while charging and mixing.
Mixer, vertical shaft
A cylindrical or annular mixing compartment having an essentially level floor and containing one or more vertical rotating shafts to which blades or paddles are attached; the mixing compartment may be stationary or rotate about a vertical axis.
The time taken for a complete cycle in a batch mixer i.e. the time elapsing between successive repetitions of the same operation (e.g. successive discharges of the mixer).
Rotation rate of a mixer drum or of the paddles in an open-top pan or trough mixer when mixing a batch; expressed in revolutions per minute (rpm) or in peripheral feet per minute of a point on the circumference at maximum diameter.
The period during which the constituents of a batch of concrete are mixed by- a mixer; for a stationary mixer time is given in minutes from the completion of mixer charging until the beginning of discharge; for a truck mixer time is given in good mixing
The water in freshly mixed sand-cement grout mortar or concrete exclusive of any previously absorbed by the aggregate (e.g. water considered in the computation of the net water-cement ratio).
The assembled blended co-mingled ingredients of mortar concrete or the like; or the proportions for their assembly.
The ratio of modulus of elasticity of steel E to that of concrete E usually denoted by the symbol n.
Modulus of deformation
A concept of modulus of elasticity expressed as a function of two time variables; strain in loaded concrete as a function of the age at which the load is initially applied and of the length of time the load is sustained.
Modulus of rigidity
The ratio of unit shearing stress to the corresponding unit shearing strain; referred to as "shear modulus" and "modulus of elasticity in shear"; denoted by the symbol G. (See also Modulus of elasticity.)
Modulus of rupture
A measure of the ultimate loadcarrying capacity of a beam and sometimes referred to as "rupture modulus" or "rupture strength". It is calculated for apparent tensile stress in the extreme fiber of a transverse test specimen under the load
Modulus of subgrade reaction
Ratio of load per unit area of horizontal surface (of a mass of soil) to corresponding settlement of the surface; it is determined as the slope of the secant drawn between the point corresponding to zero settlement and a specified point on the load-settle
A room in which the atmosphere is maintained at a selected temperature (usually 23.0?1.7 C or 73.4-13.0 F) and a relative humidity of at least 98 percent for the purpose of curing and storing cementitious test speciment; the facilities must be sufficient
An increase in dimension or bulk volume of a ceramic article caused by reaction with water or water vapor. (ASTM C 242). NOTE: This reaction may occur in time at atmospheric temperature and pressure but is expedited by exposure of the article to water
1. The movement of moisture through a porous medium; 2. The effects of such movement on efflorescence and volume change in hardened cement paste mortar concrete or rock.
1. A divider containing a cavity into which neat cement mortar or concrete test specimens are cast; 2. A form used in the fabrication of precast mortar or concrete units (e.g. masonry units).
A mineral oil that is applied to the interior surface of a clean mold before casting concrete or mortar therein to facilitate removal of the mold after the concrete or mortar has hardened. (See also Form oil Bond breaker and Release agent).
The colloquial expression for the more descriptive term bending moment.
A method of structural analysis for continuous beams and rigid frames whereby successive converging corrections are made to an assumed set of moments until the desired precision is obtained; also known as the Hardy Cross method.
A single color decoration. (ASTM C 242).
A term used for tile manufactured by a process which allows the simultaneous firing of the clay with the glaze producing a finished tile with a single firing.
A body of plain or reinforced concrete cast or erected as a single integral mass or structure. Monolithic concrete. Concrete cast with no joints other than construction.
The application of a 5/a in. (15 mm) terrazzo topping directly to a specially prepared concrete substrata eliminating an underbed.
On flatwork: a higher quality more serviceable topping course placed promptly after the base course has lost all slump and bleeding water. Monomer. An organic liquid of relatively low molecular weight that creates a solid polymer by reacting with itself
Composed of single molecules; specifically films that are one molecule thick. Denotes a thickness equal to one molecule (e.g. certain chemical compounds develop a "monomolecular film" over bleeding water at the surface of freshly placed concrete or mortar
See Montmorillonoid. Montmorillonoid. A group of clay minerals including montmorillonoite characterized by a sheet-like internal molecular structure; consisting of extremely finelydivided hydrous aluminum or magnesium silicates that swell
A mixture of cement paste and fine aggregate; in fresh concrete the material occupying the interstices among particles of coarse aggregate; in masonry construction mortar may contain masonry cement or may contain hydraulic cement with lime
The mortar hoe is used for hand-mixing mortar. The best type has a perforated blade and a handle about 66" in length. The hoe should be kept clean and free of all mortar so it can be pushed and pulled easily through a box of mortar.
Most mortar mixers are driven by gasoline combustion engines of 11/~ horsepower or greater depending on the type of sack mix. Electrically driven mixers are used when small batches of mortar are needed. The quality of machine-mixed mortar far exceeds that
Mortar pumping machine
The mortar pumping machine is used with the mortar mixer. Mixed mortar is poured into the hopper and a pneumatic gun forces the mortar through a hose. The mortar can be delivered through the hose to tilesetters working as high as 13 stories above the street
The mortarboard is used as a table to hold mortar. It is usually 30" square.
Small tile or bits of tile stone or glass. These are used to form a surface design or an intricate pattern.
Tile assembled into units or sheets by suitable material to facilitate handling and installation. Tile may be face-mounted back-mounted or edge-mounted. Face-mounted tile assemblies may have paper or other suitable material applied to the face of each tile
A slang term for mortar.
A rare mineral of theoretical composition 3A1203 2Si02 a relatively stable phase in ceramics produced by the high temperature reaction of alumina and silica or by the thermal decomposition of aluminasilica minerals such as kyanite sillimanite andalusit
A vitreous ceramic whiteware for technical application in which mullite (3AI 0 - 2Si0 ) is the essential crystalline phase. (ASTM C 242-72) Mullite whiteware. Any ceramic whiteware in which mullite (3A1 0 - 2SiO ) is the essential crystalline phase. (AST
Tile installed in a precise area of a wall or floor to provide a decorative design or picture. Glass or marble mosaic tile (tesserae) made to form a picture or design. Ceramic tile painted and fired to form a picture or design. See Decorated and Decoratio
Hydrochloric acid (30% HCL) commercial grade.
P.S.I. or psi
Pounds per square inch a unit measure of pressure.
Packing house tile
Similar to quarry tile but usually of greater thickness.
Paper and wire
'far paper and wire mesh (or metal lath) that are used as a hacking; for the installation of tile.
Paper mounted ceramic mosaics
Ceramic mosaic tiles mounted on paper. Paper is applied to face of tile in sheets approximately twelve (12) inches wide twentyfour (0-1) inches long.
Pate dure (hard paste)
A French term designating; ceramic whitewares fired at relatively high temperatures. (ASTM C 242).
Pate tendre (soft paste)
A French term designating ceramic whitewares fired at relatively low temperatures. (ASTM C 242).
Unglazed porcelain or natural clay tile formed by the dust-pressed method and similar to ceramic mosaics in composition and physical properties but relatively thicker with 6 in.- or more of facial area. (ASTM C 242).
See Orangepeel; Shivering.
Reinforcing steel rod with a diameter of Y4".
A lithium mineral of theorical composition Li O - A 120a ' 8Si02 which transforms on heating to a beta spodurnene-silica solid solution product of very low or nil thermal expansion.
Physical properties of ceramic tile
Those properties as measured by ASTM tests.
Imperfections in the surface of a ceramic body or glaze resembling pin pricks. (ASTM C 242).
Indentations in the finished surface of individtial tiles other than at the corners and edges. These are caused by sharp corners on trowels and other tools of the workmen and are different than manufacturing defects.
Development of relatively small cavities in a surface due to phenomena such as corrosion or cavitation or in concrete localized disintegration. (See also Popout. )
A cementitious material or combination of cementitious material and aggregate that when mixed with a suitable amount of water forms a plastic mass or paste which when applied to a surface adheres to it and subsequently hardens preserving in a rigid sta
Cracking that occurs in the surface of fresh concrete soon after it is placed and while it is still plastic.
See Pressing wet.
A complex property of a material involving a combination of qualities of mobility and magnitude of yield value; that property of freshly mixed cement paste concrete or mortar which determines its resistance deformation or ease of molding.
A material that increases plasticity of a cement paste mortar or concrete mixture.
Pounders per lineal inch.
Perpendicular to a true level.
An additional scratch coat that has been applied to obtain a uniform setting bed on a plumb vertical plane.
Mortar with a consistency of stiff paste. The mix is forcibly compressed into the tile joints where it hardens.
The pointing trowel or pointer is probably the most essential tool in the trade. It comes in sizes ranging from 4" to 7" in length but the 6" trowel is the most popular. The tilesetter uses this trowel in every phase of the work especially for straighten
The ratio of transverse (lateral) strain to the corresponding axial (longitudinal) strain resulting from uniformly distributed axial stress below the proportional limit of the material; the value will average about 0.2 for concrete and 0.25 for most metals
A multicolor decoration. (ASTM C 242).
A thermoplastic high-molecular-weight organic compound used in formulating protective coatings or in sheet form as a protective cover for concrete surfaces during the curing period or to provide a temporary enclosure for construction operations.
The breaking away of small portions of a concrete surface due to internal pressure which leaves a shallow typically conical depression.
A glazed or unglazed vitreous ceramic white .vare used for technical purposes. This term designates such products as electrical chemical mechanical structural and thermal wares when they are vitreous. (See also Alumina porcelain; Cordierite porcelain;
The method of producing glazed ware by which a ceraunic body and glaze are matured together in the same firing operation. (ASTM C 242).
A ceramic mosaic tile or paver that is generally made by the dust-pressed method of a composition resulting in a tile that is dense finegrained and smooth with sharply formed face usually impervious. Colors of the porcelain type are usually of a clear
apparent The relationship of the open pore space to the bulk volume expressed in percent. (ASTM C 242).
A method of prestressing reinforced concrete in which tendons are tensioned after the concrete has hardened.
The period of time during which a material maintains its workable properties after it has been mixed.
All fired ceramic wares that contain clay when formed except technical structural and refractory products. (ASTM C 242).
A siliceous or siliceous and aluminous material which in itself possesses little or no cementitious value but will in finely divided form and in the presence of moisture chemically react with calcium hydroxide at ordinary temperatures to form compounds
A concrete member that is cast and cured in other than its final position; the process of placing and finishing precast concrete.
Concrete cast elsewhere than its final position.
The term used to describe mortar that has been placed and allowed to harden prior to bonding tile to it with thin-set materials.
A surface unit consisting of an assembly of ceramic tile bonded together at their edges by a material generally elastomeric which seals the joints completely. Such material (grout) may fill the joint completely or partially and may cover all a portion
See Pressing dry; Pressing hot; Pressing wet.
Forming ceramic ware in dies from powdered or granular material by direct pressure. (ASTM C 242).
A jiggering process wherein a heated profile tool or plunger is employed. (ASTM C 242-72)
Pressing, wet(plastic pressing)
Forming ceramic ware in dies from a plastic body by direct pressure. (ASTM C 242).
Concrete in which internal stresses of such magnitude and distribution are introduced that the tensile stresses resulting from the service loads are counteracted to a desired degree; in reinforced concrete the prestress is commonly introduced by tensioning
A method of prestressing reinforced concrete in which the tendons are tensioned before the concrete has hardened.
Primary clay (residual clay)
A clay which remains geologically at its site of formation. (ASTM C 242).
See Process dry; Process wet.
Process wet (slip process)
The method of preparation of a ceramic body wherein the constituents are blended in sufficient liquid to produce a fluid suspension for use as such or for subsequent processing. (ASTM C 242).
Process, dry (dry mix)
The method of preparation of a ceramic body wherein the constituents are blended dry following which liquid may be added as required for subsequent processing. (ASTM C 242).
A highly porous and vesicular lava usually of relatively high silica content composed largely of glass drawn into approximately parallel or loosely entwined fibers which themselves contain sealed vesicles.
Concrete which is transported through hose or pipe by means of a pump.
See Neat cement.
A thin coat of pure portland cement which is used to bond tile to mortar.
A hydrated aluminum silicate mineral of the theoretical composition A12 03 - 4Si 02 - H2 O having physical properities in the raw state resembling mineral talc. (ASTM C 21)
A metal grid that is used to properly space and align floor tiles.
The procedure of spreading damp cheese cloth and pulling it over the tile surface during the tile grouting process in order to clean the tile.
Rake or rake line
The inclination from a horizontal direction.
A joint in a masonry wall which has the mortar raked out to a specified depth while it is only slightly hardened.
A glaze compounded primarily from raw constituents that is containing no prefused materials. (ASTM C 242).
A metallic or nonmetallic waterproof support for a shower stall. (TCA)
A trim unit used to reduce the radius of a bullnose or a cove to another radius or to a square. (TCA)
Concrete having refractory prop-. erties and suitable for use at high temperatures (generally about 315 to 1315 C) in which the binding agent is a hydraulic cement.
Concrete containing adequate reinforcement (prestressed or not prestressed) and designed on the assumption that the two materials act together in resisting forces.
Unit masonry in which reinforcement is embedded in such a manner that the two materials act together in resisting forces.
mesh See Welded-wire fabric and Welded-wire fabric reinforcement.
The ratio of the quantity of water vapor actually present to amount present in a saturated atmosphere at a given temperature; expressed as a percentage.
Material used to prevent bonding of concrete to a surface. (See also Bond breaker.)
The ending of a small splash wall or a wainscot at right angle to the major wall.
A semivitreous ware or earthenware having a brown or mottled brown bright glaze. Originated in England on the estate of the Marquis of Rockingham. (ASTM C 242).
The rod saw is one of the newest tools used in the cutting of tile. It is a steel rod approximately 1/s" in diameter. The rod has tungsten carbide particles embedded in the surface. The rod saw is used to cut circles or irregular curves in tile.
The act of preparing a surface by applying tar paper and metal lath (or wire mesh). Sometimes called wiring.
Cross and tee-shaped objects used to space tile on floors or walls. They are manufactured in thicknesses of 1/16" 1/8" 1/4" 3/8" and 1/2".
The rubber trowel used for grouting is a non-porous synthetic-rubber-faced float that is mounted on an aluminum back with a wood handle. This trowel is used to force material deep into tile joints and to remove excess material for a perfect finish.
A Carborundum stone that is used to smooth the rough edges of tile.
A mineral form of titanium oxide (TiO2) (tetragonal crystallization) but usually produced chemically for use in ceramics and other products. (ASTM C 21)
A term used when a wall surface has developed a slide.
A portable source of heat customarily oilburning used 'to heat an enclosure around or over newly placed concrete to prevent the concrete from freezing.
A glaze produced by the reaction at elevated temperature between the ceramic body surface and salt fumes produced in the kiln atmosphere. (ASTM C 242).
The method of obtaining tile for testing from an agreed-upon lot.
Tiny pits in the surface of the tile. Sandblast. A system of cutting or abrading a surface such as concrete by a stream of sand ejected from a nozzle at high speed by compressed air; often used for cleanup of horizontal construction joints or for exposure
A method of scarifying the surface of concrete or masonry to provide a bondable surface. Compressed air is used to propel a stream of wet or dry sand onto the surface.
Sander-grinder (Cutting tool)
In addition to sander and grinder attachment both uninstalled and installed tile. The cutting is done dry.
A cut in hardened concrete utilizing diamond or silicone-carbide blades or discs.
A joint cut in hardened concrete generally not to the full depth of the member by means of special equipment.
A temporary structure for the support of deck forms cartways or workmen or a combination of these such as an elevated platform for supporting workmen tools and materials; adjustable metal scaffolding is frequently adapted for shoring in concrete work.
A piece of thin sheet metal with teeth or serrations cut in the edge. It is used to roughen fresh mortar surfaces to achieve a good bond for the tile. A scarifies also can be used to roughen the surface of concrete. (TCA)
Surface blemishes caused by scraping or other marring of the tile.
A mixture of portland cement sand and water.
The first coat of plaster or stucco applied to a surface in three-coat work; usually cross-raked or scratched to form a mechanical key with the brown coat.
Tiles that have surface scratches (usually glazed wall tile) caused from sand tools or rough handling.
Any serrated or sharply tined object that is tised to roughen the surface of one coat of mortar to provide a mechanical key for the next coat. See also Scarifies.
The application of a scratch coat and its combing with a scratches.
To strike off mortar laying above the desired plane or shape.
Firmly established grade strips or side forms for unformed concrete which will guide the strikeoff in producing the desired plane or shape.
Tile with a decorative design of )nigh and low areas molded into the finished fare. ((:TI)
An elastomeric material that is used to fill and seal the expansion joint. This material prevents the passage of moisture and allows horizontal and lateral movement at the expansion joint.
See joint sealant.
Second grade ceramic tile
Ceramic tile with appearance defects not affecting wearing or sanitary qualities.
Secondary clay (sedimentary clay)
A clay which lilts been geologically transported from its place of formation. (ASTM C 242).
Metal lath or welded wire fabric formed in the manufacturing process to include means by which the material is held away from the supporting surface thus creating a space for "keying" of the insulating concrete plaster or stucco.
Tile with lugs spacers or protuberances on the sides. These devices automatically space the tile for the grout joints. (SS-T-308b)
A colorless or colored glaze having moderate gloss. (ASTM C 242).
A trade term designating semivitreous dinnerware. (ASTM C 242).
Less than -3 percent to 7 percent water absorption. The condition reached by a cement paste mortar or concrete when it has lost plasticity to an arbitrary degree usually measured in terms of resistance to penetration or deformation; initial set refers t
See Initial setting time and Final setting time.
The gradation of color.
Coarse sand of which the particles are of angular shape.
A wall portion of a structural frame intended to resist lateral forces such as earthquake wind and blast acting in or parallel to the plane of the wall. Shelf life. Maximum interval during which a material may be stored and remain in a usable condition
Ship and galley tile
A special quarry tile having an indented pattern on the face of the the to produce an antislip effect. (ASTM C 242).
The splintering which occurs in fired glazes or other ceramic coatings due to critical compressive stress. (ASTM C 242).
Shore A hardness
The reading of a material's hardness on a durometer the scale of which is 0-100 used on elastomers as polyacrylic esters and natural rubber. Consists of a pinpoint depression into the material the material being at least 100 mils thick. A Shore A readin
Shore D hardness
The reading of a material's hardness on a durometer similar to the Shore A durometer the scale o? which is 0-100 used on rigid and semi-rigid materials such as polystyrene. Consists of a pinpoint depression into the material. Both the Shore A and Shore D
Terminology its(-(] in some areas for Waterproof membrane. (CTI)
The floor and side walls of the shower tip to and including the curb of the shower. (CTI) Shower receptor liner or lining. Terminology used in some areas for Waterproof membrane.
The decrease in volume or contraction of a material by the escape of any volatile substance or by a chemical or physical change in the material. Shrinkage crack. Crack due to restraint of shrinkage.
Cracking of a structure or member due to failure in tension caused by external or internal restraints as reduction in moisture content develops or as carbonation occurs or both.
The common oxide of silicon usually found naturally as quartz or in complex combination with other elements as silicates. Various polymorphs and natural occurrences of silica include cristobalite tridymite cryptocrystalline chert flint chalcedony and
A measure of the frictional characteristics of a surface.
See Bond coat.
A fresh tile wall that has buckled or sagged. This condition may he caused by excessive mortar insufficient lime in the mortar or excessive moisture in the scratch coat. A slide also may result if the surface is slick or the mortar is too soft.
A suspension of ceramic material in liquid. (ASTM C 242).
A ceramic material or mixture other than a glaze. applied to a ceramic body and fired to the maturity required to develop specified characteristics. (ASTM C 242).
A glaze consisting primarily of a readily fusible clay or silt. (ASTM C 242).
See Process wet.
Tile having greater slip-resistant characteristics clue to an abrasive admixture abrasive particles in the surface or grooves or patterns in the surface.
Description of a tile that has been cut to fit arormd pipes or switch boxes. This tile is usually in the shape of the letter 11 or the letter L.
A measure of consistency of freshly mixed concrete mortar or stucco equal to the subsidence measured.
A mold in the form of the lateral surface of the frustum of a cone with a base diameter of 8 in. (203 mm) top diameter 4 in. (102 mm) and height 12 in. (305 mm) used to fabricate a specimen of freshly mixed concrete for the slump test; a cone 6 in. (152
The procedure for measuring slump.
A mixture of water and any finely divided insoluble material such as portland cement slag or clay in suspension.
A pure coat of 11 very soft consistency. This also is called a slurry coat.
A specific batch or lot of frit. (verb). The act of melting a batch of frit. (ASTM C 21). Smelter. A furnace in which the raw materials of a frit batch are melted. (ASTM C 21)
'I he method of applying a soapy film to newly tiled .valls to protect them from paint and plaster during construction. (TCA)
The underside of a part or member of a structure such as a beam stairway or arch.
A generic term for unconsolidated natural surface material above bedrock.
Oblong; tile laid with the long side vertical in(] all joints in alignment.
See Casting solid.
The dry ingredients remaining after evaporation of all volatile solvent or water. Not a fluid and not flowable.
Describes the property of a substance to dissolve in another and form a solution e.g. sugar is soluble in water.
The process by which a substance (solid liquid or gas) is homogeneously mixed with a liquid called the solvent and the mixture being incapable of mechanical separation into its components. Alloys and amalgams are solutions of metals in metal; brines ar
In a solution that substance which dissolves another is called the solvent. Solvent is also a common term for many liquids which are commonly used in making solutions e.g. organic solvents petroleum solvents etc. Also used for thinning down a fluid a
T-shaped and Y-shaped they are used in installation to separate tile on walls and floors. They are manufactured in various thicknesses from 1/16" to 1/2'.
A dry or dampened mixture of one part Portland cement and one part extra-fine sand. This mix is used as a filler in the joints of mounted ceramic mosaic tiles to keep them evenly spaced during installation.
A fragment usually in the shape of a flake detached from a larger mass by a blow by the action of weather by pressure or by expansion within the larger mass.
That part of a wall between the head of a window and the soil of the window above it.
A tile either glazed or unglazed made to meet or to have specific physical design or appearance characteristics such as size thickness shape color or decoration; keys or lugs on backs or sides special resistance to staining frost alkalies acids
The ratio of the weight of any volume of a mass or substance to the weight of an equal volume of water at a given temperature. The specific gravity of a substance times the density of water equals the density of the substance.
Any dark dots on the tile less than 1/sa inch in diameter and noticeable at a distance of more than three feet.
A glaze defect of the pinhole type developed in the decorating kiln due to evolution of minute gas bubbles from body or glaze. (ASTM C 242).
The walls of a tile drainboard or bathtub. Split L cut. An improper L cut that is made by splitting a tile instead of cutting it.
Spodumene (alpha spodumene)
A lithium mineral of the theoretical composition Li20 - A1203 - 4Si02 (monoclinic crystallization) which on heating inverts to beta spodumene a form having very low nil thermal expansion. (ASTM C 21)
Any dark dots on the face of the tile more than 1/64 inch in diameter.
noun The quantity of adhesive per unit area applied to an adherent usually expressed in pounds of adhesive per thousand square feet of area. (1) Single Spread refers to application of adhesive to only one adherent. (2) Double Spread refers to application of ad
The ability to remain unchanged; equilibrium steady constant. Ability to restore to original condition after being disturbed by some force.
A method of installation whereby glazed tiles are placed on the wall so that they are in direct contact with the adjacent tiles. The width of the joints is not maintained by the use of string or other ineans. The tiles may he set with either straight or br
Discoloration caused by a foreign matter chemically affecting the material itself.
Standard grade ceramic tile
Highest grade of all types of ceramic tile.
Curing of concrete or mortar in water vapor at atmospheric or higher pressures and at temperatures between about 100 and 420 F (40 and 215 C). (See also Autoclave curing).
A vitreous ceramic whiteware for technical application in which magnesium metasilicate (MgO - SiO ) is the essential crystalline phase. (ASTM C 242).
Massive talc or the pulverized product. thereof having the general formula 3 MgO - 4SiO H2O. (ASTM C 242).
Any ceramic whiteware in which magnesium metasilicate (NIgO - SiO ) is the essential crystalline phase. (ASTM C 242).
The steel square is one of the most important tilesetting tools. The large arm of the square is 2" wide and 24" long and is called the body or blade. The smaller arm is at a 90-degree angle to the blade and is 1l/. wide and 16 long; it is called the ton
Use of a Carborundum stone to eliminate the jagged and flaked edges due to cutting.
A vitreous or semivitreous ceramic ware of fine texture made primarily from nonrefractory fire clay. (ASTM C 242).
In the period of time during which a packaged adhesive can be stored under specified temperature conditions and remain suitable for use. Sometimes called "shelf life".
See Layout stick.
The usual style of laying tile where all the joints are in alignment.
A straight piece of lumber that is used to rod mortar and to align tile.
A masonry unit laid with its length horizontal and parallel with the face of a wall or other masonry member.
A process of removing excess grout from the joints by wiping with a sponge or cloth or scraping with a curved instrument. (TCA)
Cracks or laminations in the body of the tile which detract from the aesthetic appearances and/or the structural soundness of the tile installation.
A cement plaster used for coating exterior walls and other exterior surfaces of buildings. (See also Plaster.)
Vertical member of appropriate size (2x4 to 4x10 in.) (50x 100 to 100x250 mm) and spacing (16 to 30 in.) (400 to 750 mm) to support sheathing of concrete forms; also a headed steel device used to anchor steel plates or shapes to concrete members.
The underlying support for the ceramic tile installation.
An instrument used to test the abrasion resistance of a material.
All utensils and decorative articles used on the table for meal service. (ASTM C 242).
Someone who can read blueprints and is familiar with the specifications. This person makes tracings of special details concerning the tilework after gathering the necessary information and then estimates the labor materials tile quantities and special t
An inspection technique whereby a coin key or other small metallic object is tapped against an installed tile to determine by sound whether the tile is completely bonded to its hacking.
The pulling force necessary to break a given specimen divided by the cross sectional area. Units given in lbs./in2 (P.S.I.). It measures the resistance of a material to stretching without rupture. Normally is not used with reference to elastic materials.
Hard baked clayware including tile of variable color averaging reddish red-yellow in hue and of high saturation. (CTI)
A porous red clayware characterized by embossed decorations of the same color and a satin-like unglazed surface. Originated on the Island of Samos. (ASTM C 242).
See Concrete terrazzo.
A terrazzo surface on a port and cement and sand body made by a mixture of marble chips and portland cement and usually ground smooth. (CTI)
tessarae A small chip of glass or marble used in mosaic formations. (CTI)
A trial examination observation or evaluation used as a means of measuring a physical or chemical characteristics of a material or a physical characteristic of a structural element or a structure.
A device for applying test conditions and accurately measuring results.
Testing of ceramic tile
The act of determining whether ceramic tile are acceptable. See Physical properties of ceramic tile.
Ability of a material to conduct heat; physical constant for quantity of heat that passes through unit volume of a substance in unit of time when difference in temperature of two opposite faces is one degree.
A term used to describe the bonding of tile with suitable materials applied approximately 1/8"' thick. See also Dry-Set mortar.
The 18-gauge galvanized wire used in construction work.
A ceramic surfacing unit usually relatively thin in relation to facial area made from clay or a mixture of clay and other ceramic materials called the body of the tile having either a glazed or unglazed face and fired above red heat in the course of ma
See definition for Mounted tile.
The the cutter is one of the most efficient and economical tools in the tilesetting trade. A popular model is the hand-drawn tile cutting board that is adjustable.
Tile assembled into units or sheets and bonded together to facilitate handling. (TCA) Back-mounted tile. Mounted tile with perforated paper fiber mesh or other suitable bonding material applied to the backs or edges of the tile so that a relatively large
Tin Oxide (Sri OQ)
In finely ground form used in glazes as an opacifier.
A vitreous ceramic whiteware for technical application in which titania (TiO ) is the essential crystalline phase. (ASTM C 242).
Any ceramic whiteware in which titania (TiO ) is the essential crystalline phase. (ASTM C 242).
Tongue and groove
A type of lumber or precast concrete pile having mated projecting and grooved edges to provide a tight fit abbreviated "T & G."
A trammel bar which is easy to construct is more accurate than many other layout tools. It is used to erect perpendicular lines and to bisect angles. The tilesetter can make a trammel bar from a stick of a size that is suitable for the particular job.
A batch of concrete prepared to establish or check proportions of the constituents.
Units of various shapes consisting of such items as bases caps corners mouldings angles etc. necessary or desirable to make a complete installation and to achieve sanitary purposes as well as architectural design for all types of tile work. (ASTM C